Heat Pump Technology and Domestic Air Source Heat Pump Course.

Trainees should have 

- a minimum N/SVQ Level 2/3 in Plumbing or equivalent earlier certication; orN/SVQ Level 2/3 in Heating and Ventilating (Domestic Installation) or equivalent earlier certication; or N/SVQ Level 2/3 in Heating and Ventilating (Industrial and Commercial Installation) or equivalent earlier certication; or N/SVQ Level 2/3 in Oil-Fired Technical Services or equivalent earlier certication; or N/SVQ Level 2/3 in Gas Installation and Maintenance or equivalent earlier certication; or Heating installers with minimum 3 years of experience installing wet central heating systems, evidenced either by manufacturer courses certication or Gas Safe Register, OFTEC, MCS or HETAS registration

**AND if not included in the above qualication**

- Low Temperature Heating Water Regulations/Water Byelaws Stand-alone technical certicates/Vocationally Related Qualications (VRQ) (non-competency based) are NOT acceptable

The training manual allows you to study in your own time, at your own pace, to reduce the time spent on the training course to a minimum. It is important that you study the content of the manual prior to attending the course to ensure that you are properly prepared and can take part in discussions during the course.

Recognised as a demonstration of competence for the Microgeneration Certication Scheme (MCS).

The manual includes: Heat pumps in context. How a Heat pump works – principles and components Insulation, heat losses and the eect of heating system design Domestic hot water, buer tanks and solar coils Ground heat exchangers Health and Safety Heat pump installation Maintenance and fault finding.

Heat Pump Technology and Domestic Air Source Heat Pump Course.

Trainees should have a minimum N/SVQ Level 2/3 in Plumbing or equivalent earlier certication;...

Domestic Air Source Heat Pump 3 day Course

This 3 day package is for Gas Engineers to renew their ACS. The course covers:

CCN1 (inc CPA1), CENWAT, CKR1 & HTR1

You can swap CKR1 or HTR1 for MET1 if required.

ACS reassessments - package 

Joe Ferris

Very knowledgeable tutors . Take the time to guide you through the course and answer whatever questions you may have . The office side of the college is also very helpful 

Jerry  Hake

A friendly place to attend , and good communication regarding booking. Have used in the past & will do so again in the future. 

Alexander Davis

Very happy with service.  Initial stages signing up smooth and informative. Nikki was very helpful and  even managed to get me on a course late notice where other  competitors could not. Also would like to thank John the assessor who was very knowledgeable and was a pleasure to meet him and all staff i came into conversation with. 

Could improve on - Heating 

Garry  Tucker 

I have been to a few centres but they are not as good as you lot. I felt a ease and very supported on the days. Thank you to John and Tony.

ROSS COUZENS

Course was really good on price and the website was easy to use, extra training day was very useful to refresh your brain and put me in good stead to do my ACS reassessment a week later, big thanks to John and tony (makes a lovely cup of tea) who put us through the assessment, defo book with BGT if I do the course again.

This 3 day package is for Gas Engineers to renew their ACS. The course covers:

CCN1 (inc CPA1), CENWAT, CKR1 & HTR1

You can swap CKR1 or HTR1 for MET1 if r...

This course is for engineers who are RENEWING their current Unvented qualification.

Please see our separate listing if you would like to do this course for the first time.

This course is for engineers who are RENEWING their current Unvented qualification.

Please see our separate listing if you would like to do this course for ...

Domestic Hot Water Heating Systems Unvented G3 Renewal

This 2 day course is aimed primarily at practicing plumbers and heating engineers who already have an understanding of the fundamental requirements of central heating systems and who wish to design and install energy efficient low temperature hot water heating systems that may use heat pumps as the heat source.

This is also a pre-requisite for the 3 day Heat Pump Course.

This 2 day course is aimed primarily at practicing plumbers and heating engineers who already have an understanding of the fundamental requirements of centra...

Low Temperature Hot Water Heating Systems

These assessments are for engineers who have undergone the extension of scope mandatory training and are now doing the initial assessments.

CKR1 & HTR1 acs initial assessments

This EAL Level 3 award 603/2625/6 has been put together to replace the old City & Guilds 2391 qualification which has now expired. It is an alternative qualification to the City & Guilds 2391-52 electrical course. All the exams and assessments associated with this EAL course are undertaken before you leave the training centre, to give you the best chance of getting the result you deserve.

EAL here are an awarding body, equivalent to City & Guilds. This qualification is recognised by Ofqual and accepted by employers in the industry and the Part P Scheme Providers.

The objective of the EAL Inspection and Testing Course is to give you a good understanding of the theory and practices required to do both a periodic inspection and initial verification, and commissioning of electrical installations. The course will improve both your inspection, testing and periodic inspection skills.

Our EAL Level 3 Inspection, Testing & Periodic Course includes the following:

Initial verification
Inspection of installations
Safe isolation and testing
Certification
Inspection and testing requirements
Completion of periodic inspection
Test results interpretation
Completion of EICRs

Level 3 Award in the Periodical Inspection, Testing and Certification of Electrical Installation.

Richmond Atinga

Well structured and well delivered course. Paul Smith (instructor) very knowledgeable and patient with candidates to ensure understanding. Happy with results, would recommend. 

Dave Dowden

This Qualification provides an opportunity for electricians to refresh their practical skills and knowledge prior to undertaking the EAL Level 3 Award in the...

National Insurance

National Insurance Number 

Invoice Details 

Invoice Address & Company Name (if applicable)

Course Literature

Yes 

Not Required 

I confirm that I am aware the Course Literature is charged at an extra cost of £134 ( full set) and will be invoiced separately

A combined session to renew existing water regulations and unvented qualifications.

Water Regulations & Unvented Renewal

Water regulations one day course for plumbers and heating engineers. 

Water Regulations

Question 1

What is your address?

This is an initial assessment for first time learners.

This course aims to help plumbers and heating engineers who want to install Vented and Unvented Domestic Hot Water Storage Systems to comply with the appropriate Building Regulations and Standards.

Trainees must hold a recognised trade qualification e.g. NVQ/SNVQ Level 2 or 3 in Plumbing and Heating, or Domestic Heating, which will include Water Regulations, or be working towards one and hold Water Regulations or have evidence of a number of years experience in the plumbing or heating industry and hold Water Regulations.

Domestic Hot Water Heating Systems (Unvented G3)

Chris Jennings

Great course and the tutor was good at explaining the course throughout the day. Felt welcome and was comfortable 

Steven  Blake

Great knowledge and presenting from tutor

Mark Medlicott

Great training. Comprehensive and hassle free. Relaxed environment and knowledgeable trainer. Did my unvented renewal and will be booking my ACS renewals next year there too. Excellent service. 

Domestic Hot Water Heating Systems (Unvented G3) Initial

Sam Holder

This course aims to help plumbers and heating engineers who want to install Vented and Unvented Domestic Hot Water Storage Systems to comply with the appropr...

Domestic Air Source Heat Pump 3 day Course

Age Requirement